sdhci O2 Micro pio x86_64

[Loki]

Добрый день,
07:02.2 Generic system peripheral [0805]: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01)

Код:

sdhci [sdhci_transfer_pio()]: PIO transfer complete.
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000022
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
mmc0: req done (CMD18): 0: 00000900 00000000 00000000 00000000
mmc0:     65536 bytes transferred: 0
mmc0:     (CMD12): 0: 00000b00 00000000 00000000 00000000
mmc0: starting CMD18 arg 138b1e00 flags 000000b5
mmc0:     blksz 512 blocks 128 flags 00000200 tsac 100 ms nsac 0
mmc0:     CMD12 arg 00000000 flags 0000049d
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000020
sdhci [sdhci_read_block_pio()]: PIO reading
sdhci [sdhci_read_block_pio()]: PIO reading

Код:

07:02.2 Generic system peripheral [0805]: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01)
        Subsystem: Mitac Unknown device 8258
        Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at 64004800 (32-bit, non-prefetchable) [size=256]
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

07:02.3 Mass storage controller: O2 Micro, Inc. Integrated MS/xD Controller (rev 01)
        Subsystem: Mitac Unknown device 8258
        Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at 64001000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

конфиг ядра...
CONFIG_MMC=y
CONFIG_MMC_DEBUG=y
CONFIG_MMC_BLOCK=y
CONFIG_MMC_BLOCK_BOUNCE=y
CONFIG_MMC_SDHCI=y
в файле
./drivers/mmc/host/sdhci.c
нашел такие коменты 0o. У меня х86_64, в какую сторону можно начать
раскапывать для использования всей ширины адресной шины?

Код:

/* Controller has an unusable DMA engine */
#define SDHCI_QUIRK_BROKEN_DMA                          (1<<5)
/* Controller can only DMA from 32-bit aligned addresses */
#define SDHCI_QUIRK_32BIT_DMA_ADDR                      (1<<6)

И еще подскажите вот что...
Зачем делать инклуд, если хедер все равно пустой?
ls -al ./include/config/mmc/sdhci.h
-rw-r--r-- 1 root root 0 Июл 22 20:45 ./include/config/mmc/sdhci.h
вот тут прочитал
http://www.mjmwired.net/kernel/Documentation/DMA-mapping.txt
scenario is a 64-bit capable device.  The approach here is to try for 64-bit DAC addressing

Код:

156		int using_dac;
157	
158		if (!pci_set_dma_mask(pdev, DMA_64BIT_MASK)) {
159			using_dac = 1;
160		} else if (!pci_set_dma_mask(pdev, DMA_32BIT_MASK)) {
161			using_dac = 0;

А значения (1<<6) и (1<<5) все те же?